tkv
12-28-2007, 11:07 AM
How to config TCP/IP for static addressing
Open Network Connections.
Right-click the network connection you want to configure, and then click Properties.
On the General tab (for a local area connection) or the Networking tab (for all other connections), click Internet Protocol (TCP/IP), and then click Properties.
Click Use the following IP address, and do one of the following:
For a local area connection, in IP address, Subnet mask, and Default gateway, type the IP address (http://ip%20address/) IP address
For Internet Protocol version 4 (IPv4), a 32-bit address used to identify a node on an IPv4 internetwork. Each node on the IP internetwork must be assigned a unique IPv4 address, which is made up of the network ID, plus a unique host ID. This address is typically represented with the decimal value of each octet separated by a period (for example, 192.168.7.27). You can configure the IP address statically or dynamically by using Dynamic Host Configuration Protocol (DHCP). For Internet Protocol version 6 (IPv6), an identifier that is assigned at the IPv6 layer to an interface or set of interfaces and that can be used as the source or destination of IPv6 packets.
, subnet mask, and default gateway addresses.
For all other connections, in IP address, type the IP address.
Click Use the following DNS server addresses.
In Preferred DNS server and Alternate DNS server, type the primary and secondary DNS server (http://dns%20server/) DNS server
A server that maintains information about a portion of the DNS database and that responds to and resolves DNS queries.
addresses.
To configure advanced static address settings for a local area connection, click Advanced, and do one or more of the following:
To configure additional IP addresses:
On the IP Settings tab, in IP addresses, click Add.
In TCP/IP Address, type an IP address in IP address and a subnet mask in Subnet mask, and then click Add.
Repeat steps 1 and 2 for each IP address you want to add, and then click OK.
To configure additional default gateways:
On the IP Settings tab, in Default gateways, click Add.
In TCP/IP Gateway Address, type the IP address of the default gateway in Gateway. To manually configure a default route metric, clear the Automatic metric check box and type a metric in Metric.
Click Add.
Repeat steps 1 through 3 for each default gateway you want to add, and then click OK.
To configure a custom metric for this connection, clear the Automatic metric check box, and then type a metric value in Interface metric.
Open Network Connections.
Right-click the network connection you want to configure, and then click Properties.
On the General tab (for a local area connection) or the Networking tab (for all other connections), click Internet Protocol (TCP/IP), and then click Properties.
Click Use the following IP address, and do one of the following:
For a local area connection, in IP address, Subnet mask, and Default gateway, type the IP address (http://ip%20address/) IP address
For Internet Protocol version 4 (IPv4), a 32-bit address used to identify a node on an IPv4 internetwork. Each node on the IP internetwork must be assigned a unique IPv4 address, which is made up of the network ID, plus a unique host ID. This address is typically represented with the decimal value of each octet separated by a period (for example, 192.168.7.27). You can configure the IP address statically or dynamically by using Dynamic Host Configuration Protocol (DHCP). For Internet Protocol version 6 (IPv6), an identifier that is assigned at the IPv6 layer to an interface or set of interfaces and that can be used as the source or destination of IPv6 packets.
, subnet mask, and default gateway addresses.
For all other connections, in IP address, type the IP address.
Click Use the following DNS server addresses.
In Preferred DNS server and Alternate DNS server, type the primary and secondary DNS server (http://dns%20server/) DNS server
A server that maintains information about a portion of the DNS database and that responds to and resolves DNS queries.
addresses.
To configure advanced static address settings for a local area connection, click Advanced, and do one or more of the following:
To configure additional IP addresses:
On the IP Settings tab, in IP addresses, click Add.
In TCP/IP Address, type an IP address in IP address and a subnet mask in Subnet mask, and then click Add.
Repeat steps 1 and 2 for each IP address you want to add, and then click OK.
To configure additional default gateways:
On the IP Settings tab, in Default gateways, click Add.
In TCP/IP Gateway Address, type the IP address of the default gateway in Gateway. To manually configure a default route metric, clear the Automatic metric check box and type a metric in Metric.
Click Add.
Repeat steps 1 through 3 for each default gateway you want to add, and then click OK.
To configure a custom metric for this connection, clear the Automatic metric check box, and then type a metric value in Interface metric.